International Journal Publication

Dye-sensitized solar cells with a micro-porous TiO2 electrode and gel polymer electrolytes prepared by in situ cross-link reaction

Author affiliations and roles
  1. aIndustrial Technology Research Institute
  2. bNational Taiwan University
  3. cNational Yang Ming Chiao Tung University
  • *Corresponding author: Ho, Kuo-Chuan.

Solar Energy Materials and Solar Cells, 93, 2003–2007 (2009).

Research topic: Dye-Sensitized Solar Cells

Abstract

The ionic conductivities and performances of dye-sensitized solar cells(DSSCs) of gel polymer electrolytes(GPEs) prepared by in situ cross-link reaction with different cross-linkers were investigated. The poly(imidazole-co-butylmethacrylate)-based GPE containing the 1,2,4,5-tetrakis(bromomethyl)benzene (B4Br) cross-linker showed a higher ionic conductivity than that containing cross-linkers with a linear structure, due to the formation of micro-phase separation that resulted in an increase in ion transport paths in the GPE. Moreover, the co-adsorbent((4-pyridylthio) acetic acid, PAA) co-adsorbed with N3 dye on the TiO2 electrode not only reduced dye aggregation, but also reacted with the cross linkers in the GPE at the TiO2/GPE interface. A decrease in the charge transport resistance at the TiO2/GPE interface was noted after forming the gel; thus the value of J(SC) significantly increased from 7.72 to 10.00 m A cm(-2). In addition, in order to reduce the ionic diffusion resistance within the TiO2 electrode, incorporation of monodispersed PMMA in the TiO2 paste was considered. With the optimal weight ratio of PMMA/TiO2 (w/w 3.75), the TiO2 electrode exhibited larger pores (ca. 350 nm) uniformly distributed afters intering at 500 degrees C, and the ionic diffusion resistance within the TiO2 film could significantly be reduced. The cell conversion efficiency increased from 3.61% to 5.81% under illumination of 100 mW cm (-2), an improvement of ca. 55%. (C) 2009 Elsevier B. V. All rights reserved.

Keywords

Co-adsorbentIn situ cross-link reactionDye-sensitized solar cellsMicro-porous TiO2 electrode

OpenAlex citation history

Citations by year

40 assigned citations
  1. 12009
  2. 42010
  3. 62011
  4. 52012
  5. 62013
  6. 62014
  7. 12015
  8. 12016
  9. 32017
  10. 32018
  11. 22019
  12. 02020
  13. 12021
  14. 02022
  15. 12023
  16. 02024
  17. 02025
  18. 02026
Source: OpenAlex · Last updated 2026-09-14. Zero-citation years are included.
View citation counts as a table
YearCitations
20091
20104
20116
20125
20136
20146
20151
20161
20173
20183
20192
20200
20211
20220
20231
20240
20250
20260

OpenAlex citing works

Articles citing this work

40 citing articles with DOI, from 40 records indexed by OpenAlex.

  1. The evolution of organic materials for efficient dye-sensitized solar cells ↗

    Journal of Photochemistry and Photobiology C Photochemistry Reviews · vol. 55, pp. 100586, 2023

    DOI: 10.1016/j.jphotochemrev.2023.100586

  2. The Characterization of Dye-Sensitized Solar Cell Modified by Reduced Graphene Oxide- and ZrO2-Doped TiO2 Nanofibers at Low Light Intensities ↗

    IEEE Transactions on Electron Devices · vol. 68, no. 3, pp. 1155-1161, 2021

    DOI: 10.1109/ted.2021.3052154

  3. Prickly pear fruit extract as photosensitizer for dye-sensitized solar cell ↗

    Spectrochimica Acta Part A Molecular and Biomolecular Spectroscopy · vol. 228, pp. 117686, 2019

    DOI: 10.1016/j.saa.2019.117686

  4. Percolation Effects in Electrolytically Gated WS2/Graphene Nano:Nano Composites ↗

    ACS Applied Materials & Interfaces · vol. 11, no. 8, pp. 8545-8555, 2019

    DOI: 10.1021/acsami.8b21416

  5. Advantages of Polymer Electrolytes Towards Dye‐sensitized Solar Cells ↗

    Source not supplied by OpenAlex · pp. 121-167, 2018

    DOI: 10.1002/9781119437499.ch5

  6. Photofabrication of Highly Transparent Platinum Counter Electrodes at Ambient Temperature for Bifacial Dye Sensitized Solar Cells ↗

    Scientific Reports · vol. 8, no. 1, pp. 12864, 2018

    DOI: 10.1038/s41598-018-31040-1

  7. Fabrication and characterization of dye-sensitized solar cells based on natural plants ↗

    Chemical Physics Letters · vol. 693, pp. 16-22, 2018

    DOI: 10.1016/j.cplett.2018.01.008

  8. Effect of solvents in the extraction and stability of anthocyanin from the petals of Caesalpinia pulcherrima for natural dye sensitized solar cell applications ↗

    Journal of Materials Science Materials in Electronics · vol. 28, no. 13, pp. 9882-9892, 2017

    DOI: 10.1007/s10854-017-6743-7

  9. Use of organic materials in dye-sensitized solar cells ↗

    Materials Today · vol. 20, no. 5, pp. 267-283, 2017

    DOI: 10.1016/j.mattod.2017.01.012

  10. Enhancement in the photostability of natural dyes for dye-sensitized solar cell (DSSC) applications: a review ↗

    International Journal of Energy Research · vol. 41, no. 10, pp. 1372-1396, 2017

    DOI: 10.1002/er.3703

  11. A cascading gradient pore microstructured photoanode with enhanced photoelectrochemical and photocatalytic activities ↗

    Journal of Catalysis · vol. 344, pp. 411-419, 2016

    DOI: 10.1016/j.jcat.2016.09.017

  12. Spacer Thickness‐Dependent Electron Transport Performance of Titanium Dioxide Thick Film for Dye‐Sensitized Solar Cells ↗

    Journal of Nanomaterials · vol. 2015, no. 1, 2015

    DOI: 10.1155/2015/680201

  13. Spectra of functionalized operators arising from hypersurfaces ↗

    Zeitschrift für angewandte Mathematik und Physik · vol. 66, no. 3, pp. 631-662, 2014

    DOI: 10.1007/s00033-014-0443-4

  14. Effect of organic dye on the performance of dye-sensitized solar cell utilizing TiO2 nanostructure films synthesized via CTAB-assisted liquid phase deposition technique ↗

    Russian Journal of Electrochemistry · vol. 50, no. 11, pp. 1072-1076, 2014

    DOI: 10.1134/s1023193514080114

  15. Morphological, optical, structural and photoelectrochemical properties of TiO2nanoflower prepared via PVP surfactant assisted liquid phase deposition technique ↗

    Journal of Experimental Nanoscience · vol. 10, no. 12, pp. 925-936, 2014

    DOI: 10.1080/17458080.2014.933494

  16. Effect of titanium isopropoxide addition in low-temperature cured TiO2 photoanode for a flexible DSSC ↗

    Journal of Sol-Gel Science and Technology · vol. 72, no. 1, pp. 67-73, 2014

    DOI: 10.1007/s10971-014-3427-0

  17. Effect of pore size/distribution in TiO2 films on agarose gel electrolyte-based dye-sensitized solar cells ↗

    Journal of Solid State Electrochemistry · vol. 18, no. 6, pp. 1665-1671, 2014

    DOI: 10.1007/s10008-014-2401-7

  18. Electrospun Oxide Nanofibers for Dye-Sensitized Solar Cells ↗

    Nanostructure science and technology · pp. 111-139, 2014

    DOI: 10.1007/978-3-642-54160-5_5

  19. Physically Stable Polymer‐Membrane Electrolytes for Highly Efficient Solid‐State Dye‐Sensitized Solar Cells with Long‐Term Stability ↗

    Advanced Energy Materials · vol. 4, no. 3, 2013

    DOI: 10.1002/aenm.201300489

  20. Effect of polyethylene glycol on porous transparent TiO2 films prepared by sol–gel method ↗

    Ceramics International · vol. 40, no. 1, pp. 2209-2220, 2013

    DOI: 10.1016/j.ceramint.2013.07.139

  21. Zinc oxide-based dye-sensitized solar cells with a ruthenium dye containing an alkyl bithiophene group ↗

    Journal of Power Sources · vol. 246, pp. 1-9, 2013

    DOI: 10.1016/j.jpowsour.2013.05.101

  22. Preparation and photoelectrochemical performance of PbSe/BaTiO3/TiO2 composite film ↗

    Journal of Sol-Gel Science and Technology · vol. 67, no. 3, pp. 660-664, 2013

    DOI: 10.1007/s10971-013-3073-y

  23. Photoinduced polymerization: An innovative, powerful and environmentally friendly technique for the preparation of polymer electrolytes for dye-sensitized solar cells ↗

    Journal of Photochemistry and Photobiology C Photochemistry Reviews · vol. 16, pp. 1-21, 2013

    DOI: 10.1016/j.jphotochemrev.2013.03.002

  24. Large Pore Nanocrystalline TiO2 Films for Quasi-Solid State Dye-Sensitized Solar Cells ↗

    Advanced materials research · vol. 662, pp. 177-181, 2013

    DOI: 10.4028/www.scientific.net/amr.662.177

  25. Critical points of functionalized Lagrangians ↗

    Discrete and Continuous Dynamical Systems · vol. 33, no. 4, pp. 1231-1246, 2012

    DOI: 10.3934/dcds.2013.33.1231

  26. Cu2S/TiO2 heterojunction applied to visible light Orange II degradation ↗

    Journal of Photochemistry and Photobiology A Chemistry · vol. 248, pp. 15-23, 2012

    DOI: 10.1016/j.jphotochem.2012.08.013

  27. Preparation of highly porous TiO2 nanofibers for dye-sensitized solar cells (DSSCs) by electro-spinning ↗

    Applied Surface Science · vol. 261, pp. 343-352, 2012

    DOI: 10.1016/j.apsusc.2012.08.012

  28. Variational Models of Network Formation and Ion Transport: Applications to Perfluorosulfonate Ionomer Membranes ↗

    Polymers · vol. 4, no. 1, pp. 630-655, 2012

    DOI: 10.3390/polym4010630

  29. Analysis of the light absorption enhancement in polymer solar cell with TiO2 optical spacer ↗

    Acta Physica Sinica · vol. 61, no. 20, pp. 207203, 2012

    DOI: 10.7498/aps.61.207203

  30. Quasi‐Solid‐State Dye‐Sensitized Solar Cells Using Nanocomposite Gel Polymer Electrolytes Based on Poly(propylene carbonate) ↗

    Macromolecular Chemistry and Physics · vol. 212, no. 23, pp. 2583-2588, 2011

    DOI: 10.1002/macp.201100473

  31. Photochemical energy conversion ↗

    Photochemistry · pp. 112-190, 2011

    DOI: 10.1039/9781849732826-00112

  32. Quasi-solid-state dye-sensitized solar cells assembled by in-situ chemical cross-linking at ambient temperature ↗

    Electrochemistry Communications · vol. 13, no. 11, pp. 1284-1287, 2011

    DOI: 10.1016/j.elecom.2011.08.020

  33. Expanded graphite/pencil-lead as counter electrode for dye-sensitized solar cells ↗

    Solid-State Electronics · vol. 63, no. 1, pp. 76-82, 2011

    DOI: 10.1016/j.sse.2011.05.019

  34. Efficient quantum dot-sensitized solar cell with polystyrene-modified TiO2 photoanode and with guanidine thiocyanate in its polysulfide electrolyte ↗

    Journal of Power Sources · vol. 196, no. 15, pp. 6595-6602, 2011

    DOI: 10.1016/j.jpowsour.2011.03.084

  35. Preparation and photoelectrochemical performance of Ag/graphene/TiO2 composite film ↗

    Applied Surface Science · vol. 257, no. 15, pp. 6568-6572, 2011

    DOI: 10.1016/j.apsusc.2011.02.078

  36. Curvature driven flow of bi-layer interfaces ↗

    Physica D Nonlinear Phenomena · vol. 240, no. 7, pp. 675-693, 2010

    DOI: 10.1016/j.physd.2010.11.016

  37. Dye-sensitized solar cells with quasi-solid-state cross-linked polymer electrolytes containing aluminum oxide ↗

    Electrochimica Acta · vol. 56, no. 5, pp. 2031-2035, 2010

    DOI: 10.1016/j.electacta.2010.12.027

  38. The Effects of Co-Sensitization and Electronic Structure of Nanocrystalline N/TiO2 Anode on the Performance of Dye-Sensitized Solar Cells ↗

    Journal of Inorganic and Organometallic Polymers and Materials · vol. 21, no. 1, pp. 150-156, 2010

    DOI: 10.1007/s10904-010-9433-y

  39. In Situ Low Temperature Polymerization of Bismaleimide for Gel-Type Electrolyte for Dye-Sensitized Solar Cells ↗

    The Journal of Physical Chemistry C · vol. 114, no. 32, pp. 13832-13837, 2010

    DOI: 10.1021/jp101859r

  40. Photovoltaics literature survey (No. 74) ↗

    Progress in Photovoltaics Research and Applications · vol. 17, no. 8, pp. 594-599, 2009

    DOI: 10.1002/pip.917

← Return to publications